AutoEnginuity OBD-II ScanTool Release Notes (C) Copyright 2003 - 2008 Release Notes: This version focuses on implementing European diesel model support and finalizing new model CAN system coverage for Ford, Nissan, Chrysler, and GM for the newer models. The Nissan/Infiniti expansion will now have support for 19 new CAN systems to include the ADP, LDW, TPMS, HVEC, and HVAC. The Chrysler expansion saw improvements in the VPW-based systems finalizing any missing coverage and added 517 CAN-based system tests. The GM expansion now includes the body/chassis dual wire CAN full system support. Finally, some European diesel model support was added for the BMW, Ford, and Jaguar expansions. 09/05/2008 6.2.0 Release: ------------------------- General • Added Save Configuration support for enhanced Honda • Added Hungarian 6.X language support • Improved SpeedTracer to version 4.1 which includes more vehicle examples, new graphics, and improved connectivety • Fixed graphing issue where the live data was lost during the Print or Save message box BMW/MINI • Added E46 330d and 330xd, E39 530d, E38 730d, and E53 X5 3.0d full model support Chrysler/Dodge • Added full Anti-Lock Brakes EBC2 Module support • Added Chrysler Captiva and Sport model support • Added Chrysler HHR Panel model support • Added '07 VIN decoding for the Dodge Durango and Nitro models • Added ABS Brake bleed for the Mk25e module • Improved coverage for Anti-Lock Brakes by adding mission actuations • Improved coverage for Transmission Control Module by adding missing actuations • Improved coverage for Transmission Control Module by adding System Tests Torque Converter Clutch Break-In, Speed Proportional Steering Test, Brake Tourque Test, Pump Test, and Pinion Factor Programming - Tire Size Programming • Improved VPW-based controllers coverage Engine, Transmission, Airbag, and ABS systems by finalizing the coverage • Added 517 new CAN-based system System Test support. Too include: • NAFTA Diesel vehicle System Test Support: Activation of AC Anti-Slugging, Diesel Particulate Filter Initialization, Diesel Particulate Filter Learning, Fuel Mean Value Adaptation Routine, IMA Injector Programming, IMA Rapid Calibration, Instantaneous DPF Regeneration Routine, Manual DPF regeneration Routine, NOx Calalyst Learning Routine, NOx Catalyst Initialization • 5.9 Liter CAN Cummins (CM849) vehicle System Test Support: 20 % Biodiesel Water In Fuel Kit, Cylinder Performance Test, Fuel Pressure Override Test, Generator Full Field Mode, Governor 3-4 Shift Valve Test, Idle Speed Set Point, Idle Up Enable, Injector Kill Test, Reset Duty Cycle Accumulators, Reset Trip Information Accumulators, Reset Aftertreatment Trip Info Accumulators, Reset NOx Adsorber Counts Accumulators, Throttle Valve Auto Zero, Throttle Valve Span, and Torque Converter Clutch Test • 6.7 Liter Cummins (CM2100) System Test Support: 20 % Biodiesel Water In Fuel Kit, Accelerator Interlock Enable, Cylinder Performance Test, Exhaust Brake Enable, Fuel Pressure Override Test, Fuel System Run-Up Test, Generator Full Field Mode, High Pressure Fuel SystemTest, Idle Shutdown Enable, Idle Speed Set Point, Injector Kill Test, Injector Quantity Adjustment Routine, Mobile DeSoot - No Min Req'd Filter, Mobile PTO Enable, Mprop Fuel System Test, PTO and Idle Up, Remote Throttle Enable, Reset Accumulators, Reset Duty Cycle Accumulators, Reset Trip Information Accumulators, Reset Aftertreatment Trip Info Accumulators, Reset NOx Adsorber Counts Accumulators, Reset Regen Filter Timers, Reset Two-Stage Dump Valve Accumulators, and Switched Max Operating Speed Enable • Moved Set Idle speed for SBEC/JTEC modules from Actuations to the System Test Ford • Added Ford of Europe complete diesel sensor support • Added Ford of Europe Injector Control Module full system support • Added Ford of Europe BCMii full system support • Added Ford of Europe 1.8L and 2.0L TDCi model Injection Correction Factor coding support • Added CAN Tire Size Programming for the 6.0L Powerstroke diesel • Added IC CAN Module Configuration for select models (more coming) • Improved Ford of Europe Focus, Mondeo, and Galaxy (petrol and diesel) model support • Improved Ford of Europe S-Max, Ka, and Transit petrol model support • Improved PATs Erase Program and security access support by reporting more error conditions GM • Added ABS dual-wire CAN full system support • Added Body Controller dual-wire CAN full system support • Added Electronic Brake Controller dual-wire CAN full system support • Added Electronic Suspension Controller dual-wire CAN full system support • Added Power Steering Controller dual-wire CAN full system support • Added Trailer Brake Controller dual-wire CAN full system support • Added Vehicle Stability Controller dual-wire CAN full system support • Added support to re-direct vehicle selection for Toyota rebadged vehicles to the enhanced Toyota expansion • Added GMC Typhoon model support • Added missing EVAP, Air Conditioning, and fan state bit data for '96 - '01 models • Added H3 Hummer '06 and '07 model support • Added Impala '07 LS engine support • Added Clear Taps System Test for Transmission Honda/Acura • Improved trouble code retrieval for CAN-based controllers Isuzu • Added full ABS system support for the Amigo • Fixed actuation support for the Amigo Jaguar • Added diesel 2.0L TDCi full engine support for S-Type and X-Type models • Added 2.0L TDCi model Injection Correction Factor coding support • Added missing FETM (Audio Control Module) bi-directional controls Nissan/Infiniti • Added Enhanced Powertrain CAN bi-directional controls and Work Support support • Added 4WD CAN full system support • Added Air Levelizing DDL2 full system support • Added Automatic Transmission CAN full system support • Added RAS and HICAS CAN full system support • Added BCM CAN variation 5, 7, and 8 full system support (including module configuration settings) • Added Meter MA CAN full system support • Added Adaptive Light CAN full system support (including Steering Angle and Leveling Alignment support) • Added HVAC2 CAN full system support • Added HVEC CAN full system support • Added Lane Camera (LDW) CAN full system support • Added Precrash Seatbelt CAN full system support • Added Rearview Camera DDL2 full system support • Added TPMS CAN full system support • Added Rogue model support • Added EX 35 model support • Improved Automatic Transmission sensor support to include new bit states for later models • Fixed some BCM controllers not updating live data because address variations between controllers Mazda • Added Premacy model full system support Toyota/Lexus • Added Avensis and Auris full model support 07/03/2008 6.1.0 Release: ------------------------- • Improved datalogging playback by allowing the user to select the sensors from a data log to playback • Improved Mode 6 update rates for both OBDII Interface and the AE Enhanced Interface by removing unnecessary sync requests • Added German language support to the 6.0 series • Added new DTC Model: Added clear All, Current, None selections to allow customizing of which controllers to clear from Added enhanced Freeze Frame support for Ford and Mazda CAN ECMs Improved Freeze Frame naming conventions to allow for certain makes to label as necessary. Such as GM to label some as Failure Records Now supports reporting Freeze Frame progress on DTC screen Now shows each controllers progress after completion. Whether there is trouble codes, no trouble codes, or no response from the controller Non-OBDII-Only no longer retrieves generic trouble codes • Fixed installation not updating the color scheme to the newest • Fixed Mode 6 reporting for CAN models where the vehicle manufacturer would not clear out previous data from subsequent responses and this data was displayed as repeating Mode 6 entries • Fixed datalogging playback issue where illegal characters in the sensor names prevented the file from parsing correctly or not at all BMW / MINI • Added Cooper '07 Convertible R50/R52 enhanced system support • Added more VIN decoding for the new models • Added SMG II system tests: Teach In Clutch Slipping, Teach In Clutch Characteristic Curve, Teach Clutch Values, and Longitudinal Acceleration Sensor Offset • Improved DME M44 system support by adding actuations and resolving various sensors • Improved trouble code reporting by removing the SAE designations (for example FC50 will no longer report as P1050 but simply as FC50) • Fixed ABS DSC 8 connection issues which caused some controllers to require multiple attempts to clearing trouble codes or report live data Chrysler • Added Tire Size programming (CAN models) • Added more body and chassis actuations • Fixed the engine module settings for the '07 Chrysler Town and Country • Fixed the engine module settings for the '07 Dodge Caravan and Grand Caravan Ford • Added enhanced CAN freeze frame support • Added Tire Size configuration support for Powerstroke 7.3L '99 - '03 models • Added network test for non-CAN controllers • Changed STFT CAN sensor to range from -25 to 35 instead of displaying as stochiometric 0 - 2.0% • Changed all RPM sensor ranges to 8000 or less • Changed all MAF sensor ranges to 655.35 • Fixed missing Mode 6 translation for TID 4c and 31 • Fixed Keyless Entry Code not showing values in Meter or Graph tabs • Fixed STFT and LTFT from not being list in some case GM • Added '06 Chevy Uplander ABS System • Added '06 - '07 7.0 Liter LS7 engine • Improved model selection by adding support for transfer case outside of the transmission field • Fixed issue with missing sensors for BCM controllers • Fixed the Left Rear and Right Front wheel speed sensor in ABS being flipped for '98 - '00 Oldsmobile • Fixed issue with missing sensors for BCM controllers • Fixed the air pump relay command for the '01 Trailblazer • Fixed an issue where the Camaro was miss-IDed as a light truck • Fixed Fuel Pressure Actuation for the 2006+ Duramax trucks • Fixed missing sensors for certain BCM controllers Honda • Added CAN system bi-directional controls • Added ABS Type 4 system tests and actuations • Added a check to verify that the selected ABS module requires using the body/chassis cable before displaying the reminder • Added OPDS and SWS Initalizations • Fixed issue with the IMA system for the '04 Civic Hybrid Hyundai/Kia • Added 4WD system support • Added EnhancedTransaxialMELCO bi-directional control support • Added Misfire and Fuel Trim PIDs to Bosch COM 1.1.0 ECM • Added EVAP Leak Test Bosch COM 1.1.0 ECM • Added EVAP Leak Test Siemens 655 Rev 17 18 and 19 ECMs • Added EVAP Leak Test Siemens 670 CAN ECM • Added Throttle Position PIDs to Bosch COM 1.1.0 and Siemens 670 ECMs • Added warning messages to failed bi-directional controls • Added Sportage '05 - '07 ABS HTC Brake Bleed support • Added Steering Angle Alignment and Variant Coding support for ABS ES95660Rev32 controllers • Added Spectra 07 2.0L model support • Fixed Sportage 2.7L airbag not communicating Isuzu • Release enhanced for '96 - '07 including engine, ABS, TCM, and airbags • Added another 2k trouble code descriptions Jaguar • Added Active Dampening Ride Control system support • Added more body trouble code descriptions for Ford-based models • Improved trouble code reporting by showing all trouble codes, instead of removing the duplicates • Fixed XK8 and XKR '97 - '06 Downstream O2 Bank 1 and 2 Voltages scaling issue • Fixed SType '05+ Park Aid Module trouble code retrieval failing to retrieve single trouble codes Land Rover • Added TCM Adaption Reset support to Ford-based models • Added more body trouble code descriptions for Ford-based models • Added support for No Data text response to be displayed when the vehicle responds with a valid response that data is unavailable as opposed to reporting a zero value • Improved trouble code reporting by showing all trouble codes, instead of removing the duplicates • Improved trouble code retrieval from RCM CAN controllers by retrying in case of System Busy response. Vehicles that have a crash condition can delay their response outside of the normal time frame. Longer timing is sometimes required to resolve retrieving the trouble codes Mazda • Added full support for all Protege '00 - '03 transmission sensors • Added enhanced CAN freeze frame support • Added Throttle Position - Volts, Battery Voltage, Shift Solenoid 3, and EGR Steo Motor Status 1-4 sensors on Ford-based SCP ECMs • Fixed Barometric Pressure - HZ reporting incorrectly on Ford-based SCP ECMs • Fixed STFT and LTFT from not being list in some case • Fixed missing Mode 6 translation for TID 4c and 31 Mitsubishi • Added full VIN decoding for all models • Added new CAN Mode 6 support • Added Enhanced support 96-07 System Tests: ECU Information (ALL CAN) EVAP Leak Test (MFI CAN) EVAP Leak Monitor (MFI E200, E400, E500, E600, E1400, E1600 Series) Gas Emissions Test Mode and Sensitivy Check (ABS CAN) Zero Calibration (some OCM CANs) Service Interval Reset (Meter CAN) Tire Pressure Sensor ID Check (TPMS CAN (Front Only)) Lateral G Sensor Calibration and Air Bleed (ACD CAN) Nissan • Added more ABS trouble code descriptions • Improved Airbag Self-Diagnosis to now show the trouble code description Freeze Frame Porsche • Improved trouble code retrieval on late model Cayenne models SMART • Added VIN decoding Subaru • Fixed Rear O2 Voltage scaling • Fixed Historic trouble codes being displayed with Current codes Toyota • Improved EVAP bi-directional controls instructions 04/12/2008 6.0.2 Release: ------------------------- • Added support to prevent the use of the "Non-OBD-II Only" Vehicle Initialization Type without a Vehicle Protocol selection. BMW • Changed scaling on DME S54 / S62 for Multiplicative and Additive Adaptations to allow for negative values • Added ABS Bleed support for E46 M3 '03+ • Added Steering Angle Adjust, Lateral Acceleration, and Pressure Adjust support for E46 M3 03+ • Fixed 528i '00 ABS controller module determination Chrysler • Added ABS Mk25e DTC descriptions • Improved VIN decoding to support Wrangler '06 model • Fixed the unit conversions from mmHg to inHg Ford • Fixed Taurus and Taurus X coverage tables being swapped • Fixed retrieving trouble codes on Lincolns not completing or crashing the software • Added missing Mercury Cougar '98 enhanced powertrain support GM • Improved error handling for the CKP Relearn Test by decoding the error conditions for the user • Fixed CAN trouble code retrieval from Generic Powertrain when receiving multi-address responses, when using the AE Enhanced connector • Fixed some product lines not being displayed for '96-'97 light truck vehicles • Fixed Fuel Level sensor reporting and lack transmission system support for the '97 Chevrolet Lumina • Fixed H2 Hummer '04 model lacking enhanced systems support • Fixed an issue where enhanced powertrain was not available for a '06 Saturn ION Level 2 • Fixed the Current Misfire #1 and #2 for '01 GMC Jimmy • Fixed Purge EVAP Solenoid actuation for '03 GMC 2500 Honda • Improved SRS '06 system communication stability • Added CAN actuations for Engine, Transmission AT/CVT, and IMA Motor Type D • Added the SRS '03 trouble code support to the DTC tab • Fixed CAN trouble code retrieval from Generic Powertrain when receiving multi-address responses, when using the AE Enhanced connector • Fixed CAN Powertrain MAP sensor unit not reporting in kPa/PSI Hyundai / Kia • Added Tiburon '98 - '02 TCM support Nissan • Fixed trouble code failing to clear if the preceding controller failed to initialize Toyota • Fixed IAC Duty bi-directional control sending the command at 1/10th the requested value 03/20/2008 6.0.1 Release: ------------------------- • Added a text limit to the activation entry fields to prevent too many characters per field • Added Spanish version support • Added support PDA Dual mode activation without being connected • Fixed XML file playback not working with some files BMW • Improved EGS GS20 trouble code description coverage • Added status byte support for EGS8.32, EGS8.34, EGS8.60.2, EGS8.60.3, and EGS8.60.4 transmissions • Added X5 3.0i DME MS45 SULEV engine series support for '05 models Chrysler • Improved speed retrieving trouble codes on VPW-based Body/Chassis systems • Added the English units '03-'05 for the following sensors to read in PSI HPCR Fuel Pressure HPCR Fuel Pressure Setpoint • Fixed actuation issues for the Jeep Liberty Diesel • Fixed Min and Max values on some sensors for Jeep Liberty Diesel models • Removed the test to list only actuation support for specific vehicles. This test caused some actuations to not show up on vehicles when they where in fact supported Ford • Improved Non-CAN and CAN auto detecting sensor times by as much as 2x times • Added Keyless Entry reporting support for RAP, GEM, REM, CEM, DDM, and PDM • Added Air Bleed variation for '01 - '03 Explorer models • Fixed Powerstroke 6.4L '08 coverage being not available • Fixed system tests not showing for all Lincoln and Mercury model vehicles GM • Improved the speed of system availability test • Added Buick Terraza and Pontiac Torrent model support • Fixed H1 Hummer incorrectly showing a warning message that sensors are not supported • Fixed '05-'07 Saturn system options Truck/SVU vehicles • Fixed missing '4 Speed' transmission for the '99 GMC Serria Honda • Fixed Body Electronic-based actuations not working • Improved retrieving trouble codes for the following systems: ABS Type 1, 2, & 4 VSA Type 2 Engine Automatic Transmission CVT Transmission Infiniti • Added EX35 model support Isuzu • Added Isuzu i290 & i370 model support Jaguar • Fixed Supplimental Restraint Module for XKR '97+ not being present in supported module list • Fixed XKR '01 ABS Right Rear Wheel Speed sensor incorrectly updating when Right Front was operated Mazda • Improved CAN auto detecting sensor times by as much as 2x times Scion • Added xD model support Subaru • Fixed connection support with some Subaru models. Requires AE Enhanced Firmware 24 to resolve 03/3/2008 6.0 Release: ------------------------- • Improved hi-resolution graphing support with such features as: + Virtual buffer that can store hours of data + Full pan/zoom support + Full 32-bit color support with 16.7 million color and anti-aliased plots + Visual trigger support to show when a data reading has exceeded the range allowed + Live data mouse-over support to report plot values + Plot color-coded legend and units + Print graphs while including shop and vehicle information + Saves screen captures in BMP, JPG, GIF, and PNG • Improved user-interface responsiveness by eliminating any pending vehicle requests when a tab and is changed. Now when changing from a Live Data tab to the DTC, Test OnBoard, or OnBoard Test Results the delay will be reduced • Improved connection times by testing faster protocols first. Saves 7 to 10 seconds on a new model vehicle's connection time, while only introducing a few milliseconds to the slower protocol vehicles • Improved trouble code retrieval by only pulling generic OBD-II trouble codes when working on a powertrain system. This allows for trouble code retrieval with "Current" selection and non-powertrain systems to retrieve almost instantly • Improved access to technical support logging by adding a button to the Technical Support window to View Log from within the ScanTool software • Improved new enhanced activation support that uses hexadecimal numbers to allow for easier entry. Also, the activation code process has been streamlined to a single screen on the software • Improved documentation by adding hypertext links to the ScanTool User Guide to allow for quicker navigation of the document • Improved WBO2 sensor setup time on the O2 tab by preventing the Mode 5 data stream from being retrieved, as they don't support this • Added full support for the '07 model year on all enhanced options (except BMW models). To include GM CAN, Nissan CAN, and Toyota CAN systems support • Added support to show "No Data" in cases where the vehicle positively responded that it lacks support for the request • Added hi-resolution Vista icons • Added new connection animation • Added printing support for playback data streams • Added support for data logging initial filenames that follow the naming conventions of MAKE-MODEL-YEAR-mmm-dd-yyyy • Added new Initialization Type "CAN Force Physical Addressing" to force the CAN 11Bit physical addressing for some vehicles that do not correctly support functional addressing ('08 Nissan and '08 Subaru) • Added a wait cursor to show the time required when clearing trouble codes • Fixed data logging issue where Excel defaults to numerical values in the first column and clips the time entry • Fixed VINs not being retrieved from KWP2000 vehicles that would allow the transmission controller to report NACK while the ECM subsequently reports the VIN (i.e., BMW M6 and 6 Series) • Fixed Mercedes KWP2000 connection issues where the controller ID is 0x01 BMW • Improved data throughput on DME controllers by pre-sorting the sensor list into data groups • Improved bi-directional control support by reporting the error code reported from the controller should the request fail • Improved Engine MS45 M54 controllers sensor coverage • Added EGS model auto detection no longer requiring the user to select the correct model • Added ABS DSC8 full systems support (excluding Steering Angle Calibration) • Added X53 '04 - '06 X5 4.4L and 4.8L full systems support • Added X83 '04 - '06 X3 2.5L and 3.0L full systems support • Added 320i '02 - '05 full systems support • Added URS and AIC Rain Sensor systems support to supported MINI models • Added Electronic Height Control sensor support to supported X5 models • Added support to deactivate actuations on DME ME8 controllers that were missing this support • Added DME 5.2.1 M62 status byte support • Added ABS MK60 and DSC8 status byte support • Fixed ASC / DSC III Brake Pedal Pressure and Wheel Speed Sensors incorrectly scaled • Fixed ABS MK60 failing to clear trouble codes • Fixed 325i '03 DME not connecting because of incorrect DME tables Chrysler • Improved body and chassis trouble code retrieval by moving from the sensor list to the DTC tab • Improved bi-directional control support by reporting the error code from the controller should the request fail • Improved the speed of VPW-based Body/Chassis sensor auto detecting • Added full CAN actuation support • Added ABS CAN Brake Bleeding support • Added ABS support for '05 Dodge Cummins • Added ABS actuations support for VPW-based versions • Added ABS Bleed Brakes for VPW Modules EBC325 and MK20e • Added 3.0L engine support for the '01 Dodge Stratus • Added '96 - '98 Dodge Neon 2.0L model support • Added NGC-based system test: Module Reset • Fixed NGC-based actuations not completing in some cases • Fixed '03 Cummins communication issues with AE Enhanced Firmware V.23 Ford • Added Ford of Europe Focus CMAX model support • Added Electronic Controlled Power Steering CAN full system support for '07+ models • Added Steering Angle and Yaw Rate and Acceleration Sensor reset for IVD equipped '03 Explorer and Lincoln LS models • Added support to remove all system tests not supported by the Powerstroke diesels making correct selection easier GM • Added CAN powertrain systems support (requires new AE Enhanced to support this feature). (Body and chassis systems are coming with a single-wire CAN hardware solution later this year.) • Added missing Envoy XL system entries • Added for the 2002 Rendezvous 3.4L: Engine Oil Pressure Switch and Engine Oil Level Switch • Fixed fuel trim precision to 2 decimal places • Fixed for the '97 & '98 Oldsmobile key fob status sensor • Fixed issue with some vehicles which have 'All' as the only transmission types when there are in fact transmissions available • Changed GM module information sensors by moving them to the Vehicle Information dialog Honda • Improved SRS system detection support • Added complete system support for: + ABS Type 4 + ABS Type 3 (Ridgeline and MDX models) + IMA Motor + IMA Battery + Drive By Wire + Electric Vacuum Pump System + SWS + OPDS + Multiplex Integrated Control Unit + Relay Module + Rear Junction Unit + Multiplex Integrated Control Unit DR + Multiplex Integrated Control Unit AS + Power Window Module + Power Tail Gate + Power Slide Door Left ECU + Power Slide Door Right ECU + Driver Door ECU + Meter Module + Center Panel Module + Combination Switch Module + Center Panel Module + Auto Light ECU + Adaptive Front Lighting System ECU + Smart Entry ECU + Telematics ECU + Hands Free Telephone Module + Memory Seat Control Module + Immobilizer Module + Center Panel Module + Honda Information Platform ECU + VTM-4 + SH-AWD • Added support to display a warning if the Honda Body and Chassis cable is necessary for proper operation • Fixed issue with engine actuations not working with 5.4.1 release Hyundai/Kia • Added '96 - '00 Elantra ABS and airbag full systems support • Added '99 - '00 Elantra transaxial full system support • Added EVAP Leak Test support for Siemens 670 Rev 8 ECMs • Fixed '01 Sonata 2.5L V6 ECM not connecting Jaguar • Added '95 - '97 UK version of the XJR systems support • Added '08 U Code additions • Fixed SType '00 - '02 Restraint Control Module code retrieval failing with Current only selection SType • Fixed SType '02 Mode 6 information not being translated Land Rover • Added LR2 model full systems support • Added Restraint Occupancy Sensor Control module full support • Added Status Byte support when reporting trouble codes for late models • Added '08 U Code additions Mazda • Improved ABS sensor support to include Yaw Rate, Steering Angle, and Lateral Acceleration sensors • Improved Restraint Control Module sensor support to include all fault state sensors • Added Restraint Control Module support for RX8 '03 - '07 models • Added Occupancy Supplemental Module support for all supporting '07 - '08 models • Added ABS IVD Initialization (Lateral Acceleration and Yaw Rate Reset) • Added ABS CAN IVD Initialization • Added Restraint Control Module CAN Passenger Weight ReZero • Added GEM CAN full system support • Added Mazda CX9, Mazda2, Speed3, and Speed6 model support • Added network test for CAN-based systems • Fixed MPV '03 enhanced powertrain using the wrong protocol to communicate Nissan • Added CAN powertrain and CAN automatic transmission full systems support • Added support to show a wait cursor while retrieving the systems supported by vehicle Porsche • Added generic OBD-II sensor support within enhanced powertrain systems Subaru • Fixed enhanced powertrain systems not enumerating on certain models Toyota • Added Airbag SRS CAN full system support • Added OCC Generation 2 full system support • Added ABS CAN system actuations support • Added ABS CAN system tests Signal Check, Reset Memory, Inspection Mode, and Test Mode support • Added EFI, Airbag SRS, and ECT CAN system tests Check Mode support • Added EFI CAN Reset Memory system test support • Added support to remove sensors from the supported list based on the vehicle engine configuration. E.g. Misfire Cylinder 5 sensor on a four-cylinder vehicle • Fixed OCC Sensitivity Check system test not exiting if a different tab was selected 11/31/2007 5.4.1 Release: ------------------------- General • Fixed playback on the graphing screens where second plot uses the range of the first plot GM • Added the subwoofer actuation for the '02 Seville • Added '04 GMC Canyon LT 3.5 Liter L52 to include the 5th Cylinder and added two Transmission 4WD • Added Cruise Control PIDs for '01 Duramax • Improved Hummer support to help decode the engine, also added entries specifically for Hummers 6.5 Liter L65 (Z) - Medium Truck data stream 6.5 Liter L65 (F) - Medium Truck data stream • Fixed the minimum and maximum ranges for the 3x, 18x, 24x crank shaft sensor Honda • Added EAT support based on vehicles module ID • Fixed Generic Powertrain not being present if Enhanced support is activated Nissan • Fixed BCM not connecting or failing to communicate once connected 11/14/2007 5.4 Release: ------------------------- General • Improved Clear trouble code request warning when the vehicle refused or was busy • Improved Vehicle Selection window to show the required GM VIN characters when selecting engine and product lines • Added a warning message to alert that using Non-OBD-II Only with Generic Powertrain is not possible • Fixed Cubic Inches to Liter conversions Audi/VW • Added Mode 6 decoding for '04+ models BMW/MINI • Added support for M52 clearing individual adaptations types instead of only clearing all • Fixed naming conventions for M52 Adaption sensors to correctly follow BMW naming Chrysler • Added support for Dodge Neon '96 - '98 • Improved error handling for system tests • Fixed '06 Caravan with multiple engine type entries • Fixed retrieving and clearing transmission trouble codes • Fixed Battery Voltage and Water in the Fuel sensor readings on the CM551 Cummins module '99-'02 Ford • Added PATs programming to support master key coding • Improved the PATs programming to show any alert if security access is denied • Improved ABS CAN system support on Explorer models with AdvanTrac • Fixed typographical errors in PATs programming instructions • Fixed Coolant Temperature sensor reporting C for F unit of measure GM • Added Holden vehicle support • Added TDC Offset for the 6.5 Liter L56 (S) '96 Truck • Added a check to see if the currently selected actuation might collide with the currently selected actuations. If it might then a message is prompted to inform the user that the previous actuations may be affected by this selection • Added transmission bits and states for the '04 Chevy Impala • Improved error handling for system tests • Fixed Air Pump relay actuation for '01 Yukon • Fixed Purge Solenoid for a GMC Yukon 5.3 Liter '00 • Fixed improper engine code for engine string 3.5 Liter LX9 from L to 8 • Fixed missing transmission type for the '02 Chevy Blazer: '4 Speed' • Fixed minor BCM support issues for some passenger vehicles • Fixed scaling issues for the Spark sensor on the 3.1 Liter and 3.8 Liter Impala engines Jaguar • Added X300 '96 and '97 model year support • Added XJ12 '95 and '96 TCM system support • Added SType '99 - '02 PTEC PATs key status sensor support • Fixed SType '03 and later ABS sensor list showing 22 possible parameters not 42 Honda • Added Honda CAN support • Added transmission type selection to allow for the specific transmission support system • Added ABS Type 1 Actuations: Front Left Apply and Damper Solenoid Valves Front Left Solenoid Valves Front Left TCS Solenoid Valves Front Left VSA Solenoid and Rear Right IN Valves Front Right Apply and Damper Solenoid Valves Front Right Solenoid Valves Front Right TCS Solenoid Valves Front Right VSA Solenoid and Rear Left IN Valves Rear Left Solenoid Valves Rear Left VSA Solenoid and Front Right IN Valves Rear Right Solenoid Valves Rear Right VSA Solenoid and Front Left IN Valves Sub Throttle Valve Air Bleeding For Repair - (ABS, TCS, VSA) • Improved the speed of determining ABS system support • Improved VIN decoding • Improved error handling for system tests • Changed system DTCs to the DTC Tab for Engine, Transmission, ABS Type 1, and ABS Type 2 • Fixed some auto detecting issues for SRS03 and SRS06 systems • Fixed engine and transmission detection issues on some vehicle (ie. Honda Element 2004) Hyundia/Kia • Added Elantra and Sonata '05 - '06 2.0L engine and transmission full system support • Fixed Optima 2.5L support incorrectly using 2.7L ECM series Mazda • Added KAM Reset for supporting non-CAN models • Improved ABS support for '98+ non-CAN controllers by including all valve sensors • Improved DTC retrieval for '98 non-CAN controllers Subaru • Added a test to verify that the latest firmware is being used with enhanced Subaru support Toyota • Added HV ECU and HV Battery for '01 - '03 Prius full system support • Fixed EMPS Steering Angle Velocity showing an incorrect value if the reporting value was a negative Porsche • Added enhanced trouble code support 911 ('99-'07), Boxster ('97-'07), Cayman ('06-'07), Carrera GT ('005-'06), Cayenne ('03-'06) • Added VIN decoding support ('03+ models are equipped with this support) 09/14/2007 5.3 Release: ------------------------- General • Added support to watch for hardware being disconnected or loss of power • Added Audi/VW VIN decoding support • Improved serial number retrieval support so as to avoid the 0-XX IDs being reported by some customers • Fixed connection issues with some late model Audi/VW and Mercedes vehicles • Fixed data rates suffering because KWP2000 vehicle's transmission controller responds with a NACK BMW • Added Convertible Top Module (CVM2) sensor support • Added IHKA E53 sensor and bi-directional control support • Added IHKA E39 bi-directional control support • Added RollOver Sensor 2 (URS) sensor support • Fixed MK60 ABS controllers not enumerating properly with some Dell laptops • Fixed ZKE power window bi-directional control support Chrysler • Added Dodge Charger 2.7L '06 engine support • Added the following sensors for the '96 JTEC sensor list: Throttle Position Minimal Governor Pressure Actual Governor Pressure Target Present Gear Overdrive Off Lamp Overdrive Switch Throttle Position Output Shaft Speed Governor Pressure Duty Cycle • Added the following sensors for the '97-'00 JTEC sensor list: 3-4 Shift Solenoid Governor Pressure Actual Governor Pressure Target Governor Pressure - Volts Governor Pressure Duty Cycle Present Gear Output Shaft Speed Overdrive Off Lamp Overdrive Switch Throttle Position • Added the following sensors for the '99-'00 JTEC sensor list: Desired TC Clutch Transmission Temperature Transmission Temperature - Volts • Added engine VIN code decoding • Added Transmission support for '02 300M • Added PSI Units for the '05 Cummins HPRC sensors • Improved Cummins '06 engine sensor pulling. This removes the appearance that there is no communication with the vehicle when large blocks of sensors are selected. However this also will slow down thru-put on single sensor selections • Improved DTC retrieval from SBEC and JTEC controllers • Fixed '02 - '05 Cummins communication issues. (Enhanced Connector firmware version 19 upgrade required.) • Fixed typo for the '05 Cummins 5.9L diesel engine entry • Fixed issue with retrieving DTCs could cause sensor data communication issues • Fixed missing fault sensors for '01 ABS Mk20E controllers • Fixed no engine data for a '02 Durango Ford • Added engine VIN decoding to improve the automated vehicle selection process • Added Remote Transmitter Programming instructions to the System Test lists • Added late model IVD Initialization for ABS CAN controllers • Added Occupancy Sensor Module system support • Added ReZero Passenger Side Calibration for Airbag controllers • Added Ford of Europe models (Fiesta, Focus, Galaxy, Ka, Maverick, Mondeo, Transit) support through '06 • Improved Air Suspension bi-directional controls by showing the operational instructions GM • Added '99 & '00 5.7 Liter L31 (R) Alternative engine support and active commands • Added ABS for Product Line (Y) from '98 - '00 • Fixed communication issues for body and chassis systems • Fixed missing transmission support for Buick LeSabre '00 3.8L L36 • Fixed missing TDC Learn support for '96 GMC Suburban 6.5L diesel (Engine F) • Improved retrieving Freeze Frame information a little faster • Fixed the Engine Speed bi-directional control for the '05 Chevy Suburban 5.3L • Fixed the missing Automatic Transfer Case sensors for the '00 Chevy Blazer 4.3L L35 (W) Hyundai/Kia • Added complete ABS ES95620-03, ES95660-08, ES95660-13, ES95660-16, ES95660-17, ES95660-18, ES95660-19, ES95660-23, ES95660-32 system coverage. This completes the ABS coverage through model year '06 • Added EnhancedTransaxialL4MY04 actuation command support • Added Delphi 14 ECM and TCM support • Added Bosch CAN ECM and TCM support • Added History DTC retrieval for supporting ABS and Airbag controllers • Fixed early SRS controllers trouble code retrieval with multiple codes not properly retrieving with some Dell laptops Honda • Added Honda HRV model support • Added Acura EL model support • Added the following systems up to '06: Anti-Lock Brakes System Type 1 Anti-Lock Brakes System Type 2 Anti-Lock Brakes System Type 3 Supplemental Restraint System '96 [Special Cable Required] Supplemental Restraint System '03 Supplemental Restraint System '06 Occupant Position Detection System SWS • Fixed double sensors reporting for PGMFI module '96 - '99 Jaguar • Added '97 - '07 VDP and VDP Supercharger systems support • Fixed S-Type '05 - '07 ATC initializing the controller locking out button inputs on the vehicle • Fixed S-Type '05 - '07 ABS failing to retrieve DTCs when multiples are set • Fixed XK8 and XKR BPM DTC retrieval Mazda • Added '06 Miata MX5 system support • Added '06 MazdaSpeed system support • Improved ABS CAN sensor support to include new '06 sensors • Improved TPMS CAN sensor support to include new '06 sensors • Improved all sensor auto detection times by as much as 2x • Improved retrieving ABS trouble codes for early models • Fixed select Restraint Control Module DTC retrieval not returning codes Nissan • Added Headlamp Leveling system DTC support • Added Steering Angle Alignment function support • Added ABS Steering Angle sensor support • Fixed Powertrain controllers failing to enumerated with some Dell laptops Porsche • Added GT2 and GT3 model support • Fixed 911 models WB O2 support not listing amongst the supported sensors Subaru • Added complete enhanced Engine and Automatic Transmission for model years '99 - '07 • Added enhanced ABS for model years '05 - '07 • Added Idle RPM and Ignition Timing Retard modification support Toyota • Added enhanced ABS CAN sensor support • Improved bi-directional commands to filter out non-supported commands for from vehicles that support A4 read memory output command • Fixed EVAP bi-directional command not continuously running when left On • Fixed ABS communication timing issues which resulted in some customers reporting incorrect data 07/20/2007 5.2.1 Release: ------------------------- General • Added more Vehicle Profiles to SpeedTracer • Fixed data logging not playing back when buffer size is smaller then the buffer size or larger • Improved graphing by adding support for a tab with two graphs Ford • Added missing '96 Ford Escort enhanced support GM • Added a check to make sure we don't walk out of the payload when pulling CAN DTCs, also added the support for the multi-frame DTCs that are broken between two frames • Added Oldsmobile Product Line (N) Body/Chassis for '04 • Removed the Odometer PID from the body support of the '99 Sonoma, DPID issues incorrectly setting up • Fixed missing (R) series transmissions from light trucks '96 - '99 Honda • Added a message to verify that the AutoEnginuity Enhanced Interface is used with the Honda expansion • Fixed trouble code retrieval and clearing when not using AE Enhanced Interface and using Generic systems Hyundai/Kia • Added missing '96 - 02 Sportage 2.0L enhanced support 05/08/2007 5.2 Release: ------------------------- General • Added Dodge Sprinter to the supported vehicle list • Added Porsche Cayman and Volkswagen Polo to the supported vehicle list • Added warning for all controllers that require a special adaptor cable to be inlined to be checked when a connection was failed to be established • Improved the data logging file parsing by increasing the size of the internal buffers so large sensor lists can be processed • Improved the Spanish and German User Guide for the 5.x release • Improved the Pocket PCs BlueTooth support of enhanced interfaces (BMW, Land Rover, and Jaguar) that were long response protocols and didn't work with previous versions • Fixed AE Enhanced connector not being tested for after the first pass through the ports • Fixed compatibility issue with USB hardware not working with a PC Wireless product • Fix Pocket PC debugging logging file not being created (//My Documents//AutoEnginuity ScanTool.log) • Fix Pocket PC BlueTooth connection failing to connect after a Disconnect then Connect attempt • Fix Pocket PC clipping the VIN on the right-hand side of the display BMW • Added DME S54/S62 Electrical Fan Speed 50% and 90% • Added MS42.1 and MS41.1 smooth running PIDs support • Added MK60 ABS Bleed support (E46 non-M cars) • Fixed MK60 bi-directional controls bug with Inlet Values • Fixed DME MS42.1 DTC retrieval showing a false 00 FC code • Fixed LCMIII trouble code clearing not working • Fixed X5 4.6iS DME connection issues Chrysler • Added 2000 Chrysler Voyager and Grand Voyager to the list • Added Transmission Quick Learn for NGC based transmissions • Added Governor Pressure for JTEC vehicles • Added the ME2.8 Engine Module support (Crossfire '04-'06) • Added the EDC16C2 Engine Module support, Other systems all ready supported for (Jeep Liberty Diesel '05-'06) • Added the CR2 and CR3 Engine Support (Sprinter '04-'06) • Added the SIM-70 Engine controller for the Neon and PT Cruiser 1.6 Liter engine ('01-'05) • Added 2.7L entry for the '01 Dodge Intrepid • Added SBEC/JTEC System Tests: Erase All DTC Fault Codes Reset All Adaptive Memory Fuel Cells Reset All Non-Volatile Memory Reset CAM and Crank Misalignment Reset CAM, Crank, and Sync Status Record Reset Duty Cycle Monitor Reset Engine Running Time Record Reset Fuel Shut-off Record Reset Intake Airflow Control Stepper Motor Position Reset Trip Information Set Minimum Throttle Position to Maximum For NGC modules added reporting of: Part Number Reflash Program Counter • Added warning message if system is CCD to warn that it is not supported at this time • Changed showing of all the actuations available on a SBEC or JTEC module. Now only available actuations based on the engine size are shown • Improved sensor auto detection speed by culling sensors known not supported on models • Improved correct protocol selection algorithms • Fixed freeze frame sensor for Fuel Level having decimal place • Fixed generic powertrain from operating with enhanced option enabled • Fixed AE Enhanced communications failure with some NGC controllers (Requires firmware 5 update) • Fixed NGC-based actuations Set Idle speed, Actuate Fuel Injector, and Fuel Pump Relay not working Ford • Added Powerstroke '08 enhacned coverage support • Added all missing PATS key programming for '96 - '06 (works with all variations now) • Fixed Crown Victoria '98 and '99 having the incorrect ABS controllers in the system supported list • Improved High and Low Speed Fan Control on vehicles that report Not Supported yet will still work Jaguar • Added all enhanced systems sensor, trouble code, and actuation support for SType, XJ, XK, and XType '95-'07 • Added System Tests: Brake Sensor Setup Display Last Alarm Activations (SLM and GEM) Display Fuel Adaptation Tables Fuel Adaptation Monitor Electronic Parking Brake Release To Service Front And/Or Rear Light Calibration (ADHLS and HCM) Reset TCM Adaptations Yaw and Lateral Accelerometer Calibration Reset ABS Configurations System Self Test (SType Only GEM, REM, DDM, PDM) EVAP Leak Test • Added all '07 DTC descriptions • Improved Mode 6 support GM • Added 2004 Pontiac Bonneville Product Line H engine support • Added the EVAP Vent Solenoid Bitmap for 2003 LT 4.3 and 4.8 Liter • Added 5 bitmaps for '00 (K) LT Body Control Module, no missing sensors • Added ABS Systems for (C) - '98 -'00 and '02 -'05, (K) - '98 -'99, (W) Oldsmobile - '98 -'02 and '04, (W) Chevrolet - '00, (G) - '01 -'03 Passenger • Added 3.5 Liter for the Uplander • Added 'ATC' addition to the transmission types that are associated with Automatic Transfer Case • Fixed HeartBeat being enabled from affecting some GM controllers • Fixed door lock actuation for '99-'02 J Body BCM controller • Fixed issue with missing transmission on some vehicles (e.g. Chrysler '99 Blazer) • Fixed the EVAP Vent control for all Yukon 5.3L • Fixed the Body actuation list for Light truck's from '96 -'06 Mazda • Fixed 626 '02 enhanced coverage missing from the vehicle selection list 05/08/2007 5.1 Release: ------------------------- General • Added support to show the hardware ID in case of mismatched hardware errors so the customer can determine which is connected currently to correct the mismatch • Fixed the issue when no enhanced interface is created the system combo box does not contain any systems • Fixed the issue when there is no valid AutoEnginuity Enhanced Interface serial number, only the firmware ROM version BMW • Fixed ABS MK60 not showing 5EXX trouble code descriptions • Fixed ABS MK60 not working on the Z4 models • Added Convertible Top Module 4 trouble code and PID support • Added Safety and Information trouble code and PID support • Added Electronic Power Steering trouble code and PID support • Added Rain Sensing System PID support and Clear Adaptations system command • Added Satellite-B Pillar Left trouble code and PID support • Added Satellite-B Pillar Right trouble code and PID support Chrysler • Added 600+ U trouble code descriptions • Added 500+ P trouble code descriptions • Added 2500+ B trouble code descriptions • Added 500+ C trouble code descriptions • Added Freeze Frame display support for Non-PCode trouble codes • Added a message when pulling DTCs for VPW body and chassis systems to tell the users that the codes are displayed as sensors • Fixed pulling an extra DTC from CAN controllers • Fixed decoding engine size and body code information from VINs being pulled generically • Fixed an issue with duplicate Engine Speed PID in 2005 CAN NGC vehicles Ford • Added Injector Fault 9 and 10 for the Enhanced Powertrain CAN 6.8L models • Added full system support for '04 - '06 SuperDuty 6.8L models • Added Module ID support for non-CAN non-PCM controllers • Improved all Crown Victoria sensor support for '96 - '06 models • Fixed ABS Self-Test completing but not showing the DTCs for non-CAN controllers GM • Fixed incorrect sensors in the Body Information for the 2004 Truck K for HVAC • Fixed an issue with transmission types specific to the Auto Transfer Case not showing up causing this system to be available Honda • Added PCM and transmission actuation commands support • Added System Tests (where applicable): Crank Position Sensor Notch Learn DBW Throttle Carbon Clogging Status DBW Throttle Carbon Clogging Reset Engine Oil Replacement Reset Off-Board EVAP Test (Level 2) Resolver Zero-Position Offset Calibration Hyundai/Kia • Added more trouble code library support Mazda • Added text sensor reporting for all bit and mode sensors • Added support to retrieve Mode 33 trouble codes on ISO controllers • Added missing Protege 5 ABS and PCM for model years '01 - '03 Nissan • Added Platina model support 04/15/2007 5.0 Release: ------------------------- General • Added the ability to print the data from the Graph, Meter, Grid, and O2 tabs • Added the ability to to pause the displaying of all live data • Added a conversions calculator for Length, Mass, Pressure, Volume units • Added Hardware ROM version reporting in the About screen • Added support for Hardware-based activation codes for all our USB-based solutions • Added support to prompt the user to select the which systems to retrieve trouble codes from (current, all, or none) • Added the ability to change systems without disconnecting by pressing F7 • Added support for Mode 6 test descriptions by mousing over the test ID row • Improved connection speed by requiring the user to manually initiate the VIN retrieval if they so choose. • Improved graphing support to include two more graphs • Improved warnings for "OBD-II Not Found" and not connecting so they are more informative • Improved Windows Vista support • Fixed Live Data Grid/Graph/Meter not having translated Tool Tips • Fixed issue where a second report will be saved with the previous report name only • Fixed WB02 Voltage sensor range to correctly show the range as 0 - 8Vs • Removed BMW M3-M5 special initialization type as BMW emissions recall 06E-A03 solves their non-compliance issues • Removed the requirement that a live data tab be active for actuation controls to work Vehicle Selection • Added color-coded support to signify the vehicle selection process current status; red is used to show selected and yellow is not used • Added vehicle make specific ToolTip support for all selection fields • Added a test to make sure the interface hardware supported selected systems before continuing • Renamed Vehicle Configuration to Saved Session to clarify the true intent of the function • Improved retrieving VINs by now pulling generic first, then each enhanced interfaces method automatically Instead of forcing the user to select the make to get proper VIN retrieval methods in some cases • Improved VIN decoding by automatically setting the vehicle model to Not Selected if there is no decoded VIN BMW • Added support to decode which airbag and ABS unit the vehicle has equipped • Added complete CVM2, ZAEII and EGS832 system support • Added complete Navigation, Steering Angle System, and Airbag MRSIV sensor coverage • Added M42 M52TU bi-directional controls support • Added Navigation support to the E46 M3 and E39 M5 • Added Steering Angle System and EGS832 support to the E36 M3 • Added more RAD, and MID trouble code descriptions to the library • Added complete ABS/ASC 5.7, ABS/DSC 5.7, BIT, Airbag MRS II, NAV, SM/SML, ZKEIII, and EHC trouble code library support • Added Sleep Mode and Transport Mode support for Radio, OnBoard Module, Multi-Input Display, and Lighting Check Modules • Added displaying coding information for all models • Added displaying service and inspection information for all models • Added ABS MK20 Steering Angle adjust support • Added ABS MK60 Steering Angle, Lateral Acceleration, and Pressure adjust support • Fixed some ABS controllers initialization not completing • Fixed some EGS controllers not retrieving trouble codes with full systems retrieval Chrysler • Added '96-'98 body codes based on make/model • Added new hardware that is capable of VPW, CAN, and CCD as well as our existing SCI to our Chrysler interface • Added SBEC, JTEC, CM551, CM845, and CM848 modules other available table sensors which also include OBDII Major Monitors, Engineering Parameters, and more bitmapped sensors • Added 2006 Jeep Commander support • Added new hardware support that no longer requires device drivers and is Vista-compliant • Added more descriptions to the bi-directional controls • Added The Distance Since MIL Being Set to the sensor data list. If good trip counts has reported as zero it will not be listed under the DTCs. JTEC and Cummins under the DTC and SBEC controllers it's located in the sensor data list. If starts since failed has reported as zero it will not be listed under the DTCs • Added retrieving DTC details status for NGC modules • Added body and chassis DTCs sensor lists, to clear codes you would perform a normal code clearing • Added Freeze Frame sensors for 2004-2005 JTEC vehicles • Fixed retrieving erroneous codes for some JTEC and SBEC controllers • Fixed the double reporting of DTCs • Fixed issue with no sensor data for NGC controllers when in the past only able to read DTCs • Fixed clearing non-CAN engine codes Ford • Added text sensor reporting for all bit and mode sensors • Added full Instrument Cluster CAN sensor support • Added Lincoln Zephyr '06 enhanced systems support • Added F150 Heritage '04 enhanced systems support • Added GEM/Timer system support to all Powerstroke 6.0L vehicles • Added Trailer Brake Control system support for all supporting vehicles • Added engine size detection to VIN decoding • Added Automatic Transfer Case system support (Sensor/Actuations) • Improved ABS support for '03 - '05 Navigator and '02 - '03 Expedition • Improved HEC support for '03 - '05 Navigator and '02 - '03 Expedition • Improved '99 - '03 Powerstroke 7.3L coverage by adding a few missing PCM sensors • Fixed CAN ABS controllers single trouble code retrieval failure issue • Fixed barometric pressure PID reporting slightly too high • Fixed LTFTs not showing up in some cases • Fixed Crown Victoria '05 - '06 powertrain and ABS using the wrong protocol • Fixed '96 Yukon duplicate vehicle speed sensors listed GM • Added Air Pump Relay Active Command for 4.3 L35 Light Truck • Added ABS support for Light truck Product line 'A' and 'B' from '01 - '06 • Improved Mode 6 support • Fixed 5.7 Light Truck Powertrain sensor list to include missing O2 sensors • Fixed 3.4 Light Truck Powertrain sensor list being empty • Fixec EGR Position Error scaling for Saturn 1996 SL2 Honda • Added all enhanced powertrain support for '96 - '06 models • Added improved Mode 6 support Hyundai/Kia • Added text sensor reporting for all bit and mode sensors • Added new Delhpi ECM, ABS, airbags, and BCM controller support (requires H/K body and chassis cable) • Added Santa Fe 2.7L '05, Santa Fe 3.5L '03 - '05, Sonata 2.7L '99 - '00, '05, and Tucson V6 '04 - '05, Rio '05, Sephia '96 - '99, Sedona 3.5L '02 - '03, Sportage '96 - '99, Tiburon '03 - '05, Rondo '07, and Spectra 1.8L '96 - '99 enhanced powertrain support • Added multi-system trouble code retrieval for the controllers • Added the ability to reset the transaxle, traction control, and vehicle speed configurations for Siemens controllers • Added trouble code status byte support for Siemens controllers • Improved trouble code retrieval for the Siemens controllers • Fixed Ignition Timing PIDs not being scaled correctly Jaguar • Improved diagnostics trouble code library support Land Rover • Added all enhanced systems support 02 - 07 Mazda • Added non-Ford models '95 - '97 DTC support Nissan • Added text sensor reporting for all bit and mode sensors • Added X-Trail model support • Added support for Airbag Diagnostic Record translating the DTCs into full text descriptions • Fixed Nissan Airbag DTCs not reporting with a certain DTC count size • Fixed Nissan Idle Air Learn system test reporting failed to complete, yet the request would complete • Fixed Nissan CAN ABS front wheel speed sensors being swap right and left Subaru • Improved Mode 6 support with new entries Toyota • Added ABS CAN support • Added all ECB Utility functions support (ECB Invalid, Zero Down, and Linear Valve Offset Calibration) • Added ABS functions support (Usual and Master Cylinder Stroke) • Improved Mode 6 support • Improved bi-directional controls throughput so that the reinitializing a controller is smoother for command requests • Fixed airbag DTC support for all Scion models 01/08/2007 4.4.1 Release: ------------------------- General • Fixed Mode 6 not supported on non-Vista compliant devices • Fixed reports not showing the AutoEnginuity logo • Improved Spanish support by updating the User Guide and adding Spanish report XMLs Ford • Added GEM sensors support for 6.0L Powerstrokes Toyota/Lexus/Scion • Fixed ABS Wheel speed scaling on some vehicles reporting 10:1 to actual wheel speeds • Fixed VPW Toyotas not displaying live sensor data 11/17/2006 4.4 Release: ------------------------- General • Added Honda VIN decoding support for 1996 - 2006 models • Added a macro key (F4) for the Communication Configuration menu entry • Fixed DTCs not being retrieved immediately on the first connection in rare cases • Fixed Playback feature from reporting an error with any sensor with Time in the name • Known issue for some Honda 29Bit CAN vehicles. Auto detection may not retrieve all PIDs supported. In this case turn off Auto Detection and manually select 29Bit CAN for the Vehicle Interface Type BMW/MINI • Added BMW Status byte support for trouble code reporting • Added Seat and Steering Column Memory bi-directional controls for Head Restraint and Steering Column • Added Transport Mode Clear support for some DMEs • Added FC body/chassis controller descriptions for ABS, BMBT, RAD, IKE, ZKE, etc. • Added MKIV ABS controllers PIDs support • Fixed LCM Turn Indicator not showing any states • Fixed X5 IKE DTC retrieval not working • Fixed M3/M5 DME bi-directional controls not working • Improved the MK60 ABS controllers reporting DTCs in SAE style instead of BMW style • Fixed MK20 ABS controllers not reporting live data in some cases • Known issues with selecting ABS controllers and not seeing DTCs. Use any other controller to retrieve error codes Toyota/Lexus/Scion • Added full text descriptions for all state and mode PIDs • Added '06 complete model year support • Added Hiace, Hilux, and ES330 model support • Added OCC Sensitivity Check and Zero Calibration tests • Added EMPS Signal Check, Clear Records, and Zero Point Init/Adjust support • Added '06 Immobilizer bi-directional controls • Added '06 Power Source Control and TM Control systems support • Added TPWS Signal Check and Test Mode • Improved Mode 6 support by adding translations and scaling information for a few missing CIDs • Improved data rates for all non-CAN systems • Improved bi-directional controls for all body and chassis systems by allowing for SystemBusy responses • Fixed some controllers showing 0xBE00 unknown fault codes • Fixed OCC Weight Information sensors reporting incorrect values • Fixed DTC retrieval issues with History (Past) setting on some controllers not working • Known issues connection issues exist with TPWS and Air Conditioning on some vehicles Ford • Added Pedal Position Sensor - Volts support for the Ford Powerstrokes • Added PATS sensors support for 6.0L Powerstrokes • Improved Mode 6 support for a couple of vehicles • Fixed Mercury Grand Marquis engine controller not being set as a CAN protocol Chrysler • Added new Chrysler USB HID support • Added VIN decoding for Jeep Grand Cherokee • Fixed DTC pulling for some NGC, JTEC, and SBEC modules • Fixed DTC clearing for some NGC controllers • Fixed Dodge 2005 Stratus being mislabeled as Chrysler Stratus GM • Added ABS support for 2001 passenger C product line • Fixed resolution for the Inside Air, Outside Air, Lower Outlet, and Upper Outlet temperature sensors • Known issues when we fail to display all of the Failure Records, not enough buffer space in our current hardware design 10/03/2006 4.3.1 Release: ------------------------- General • Added Volvo VIN decoding • Added Jaguar VIN decoding • Added Jaguar Mode 6 decoding and translation • Added Land Rover Mode 6 decoding and translation • Added new Jaguar DTC library • Improved Suzuki VIN decoding • Improved KWP2000 vehicle connections • Improved the Report generation by removing the hard-coding of the "Common Files" path • Fixed Mazda Tribute VIN decoding • Fixed Pocket PC Mobile not running on Windows 2003SE by removing the Chrysler CAN support • Fixed 29Bit CAN Volvo support BMW/MINI • Added more engine trouble code descriptions • Fixed MINI Mode 6 translations Ford • Fixed Manifold Pressure PIDs not supporting a large enough range for some modified Powerstrokes GM • Added Body Product Line H 2004-2005 Mazda • Added support to determine if the selected system is available • Added the following systems support for B-series trucks Park Aid Module (ISO) Tire Pressure Monitor (PWM) Passive Anti-Theft System (PWM) Enhanced 4x4 Control (ISO) Remote Anti-Theft (ISO) Integrate Air Bag Module (ISO) • Fixed spelling issues in powertrain CAN and transmission CAN sensors Nissan • Fixed Nissan Titan Enhanced Powertrain not working Toyota Add EHPS Signal Check support Fixed ABS tests showing the wrong instructions for the test initiated Fixed Tundra models not having ABS 08/26/2006 4.3.0 Release ------------------------- General • Added Report Viewing built-into the ScanTool, so as to no longer require an XML browser • Added 29-bit CAN support • Added new Nissan/Infiniti body, chassis and network DTCs • Improved data logging playback by doubling the input stream buffer size • Improved feature activation process by reducing the steps involved • Improved Actuation window support by disabling the actuation controls when not on non-live data tabs • Fixed font settings not being restored between sessions • Fixed VPW auto detect issues for 96-98 GM family vehicles • Fixed umlaut characters not correctly being displayed with the XML reports • Fixed O2 Sensor tab dropping the connection if the O2 sensor fails to report in • Fixed meters displaying in red when the value was below 90% or less • Fixed B2S1 Wide Band O2 Sensor 2 Equivalence Ratio and Voltage showing up as B3 BMW • Added '96 - 05' ABS/ASC/DSC (MK20/60) Airbag Central (SRS) Body (ZKE/ZME/KOM) Cruise Control (GR) Engine (DME) Transmission (EGS) Heater/Air Conditioning (IHKA) Immobilizer (EWS) Instrument Cluster Mirror Memory Driver and Passenger Side (SPMBT) OnBoard Module (BM) Parking Distance Control (PDC) Radio (RAD) Seat Memory (SMF) Sliding Tilting/Roof (SMD) Steering System (LEW) Switching Center Console (SZM) Multi-Input Display (MID) Language Input System (SES) Video Module (VID) Multi-Function Steering Wheel (MFL) Navigation System (NAV) Automatic Interval Control (AIC/RLS) Air Suspension (EHC) Electric Throttle Body (EML) • Added DDE/DME/EGS Reset Adaptions • Added DDE/DME Service and Oil Interval Reset support • Added Module Information reporting for all systems • Added FC to OBDII translations for engine and transmission controllers GM • Added Module Availability Test to warn a user if a system is not present on the vehicle • Added 3x Crank Sensor support for the '99 Pontiac Montana 3.4L • Added Cruise Control system support for the '03 Montana • Added the Engine Speed for the 96 Trans Am • Added Product Line F for Passenger for years Chassis 1999-2002 • Added Passenger Chassis Product Line E - 1998-2000, W Buick - 2001-2005, D - 2003, W Olds - 2004, Y - 2004 • Added Light Truck Chassis Product Line V - 2002-2005, U - 2000-2005 • Added new chassis system 'CVRSS/ALC'• Improved misfire data for several years of passenger and light truck • Fixed Fuel Pressure Sensor reporting incorrect data for the '96 Skylark 2.4L • Fixed ABS response causing dropped packets with PCM responses • Fixed invalid body active commands for the ’98 Olds Intrigue • Fixed 4.3L (W) '96 Blazer EGR Desired fixed at 198% • Fixed 4.8L LR4 (K) '04 Tahoe missing cylinders 7 and 8 misfire data • Fixed No Communication errors from Saturn Body block commands • Fixed active commands Vent Solenoid and Fuel Trim Reset for '96 Blazer • Fixed an issue where the transmission types for some makes where missing • Fixed missing product lines in the drop down list • Fixed engine decoding issues from '96-'99 • Fixed several sensors for 2000-2002 6.0 liter and 6.6 Liter Engine and Transmission • Fixed the broadcasting messages with the multi-packet request for only one response • Fixed some spelling errors on some sensors • Corrected the FTP and EGR Decel for 96 and 97 2.4 Liter engines (N) Chrysler • Added enhanced CAN systems support (to include: Airbag, ECM, ABS, transmissions, etc.) • Added 2.4 L Dodge Neon to 2003 • Added more Cummins sensors: High Pressure Command Fail Fuel Pressure High Pressure Command Fail Fuel Pressure Set Point Fan Clutch 1 PWM Duty Cycle Cylinder Contribution 1-6 Cylinder Bank Contribution 1-2 • Added more Cummins SCI bi-directional controls Reset Duty Cycle Monitor Reset Trip Information Cylinder 1-6 Cutout Generator Field Test mode Transmission VFS PWM Transmission TCC Transmission Overdrive Lift Pump Test Cylinder Performance Test High Pressure Safety Valve Test • Added more SCI bi- directional controls Reset CAM, Crank and Sync Status Record Reset Fuel Shut-off Record Reset Engine Running Time Record Reset All Non-Volatile Memory Evaporative System Monitor Service Test Mode Misfire Monitor Service Test Mode EGR Solenoid Test Mode - Backpressure System EGR Solenoid Test Mode - Linear System Torque Converter Clutch Solenoid Test Mode 3-4 Gear Shift Solenoid Test Mode Reset All Adaptive Memory Fuel Cells Reset Intake Airflow Control Stepper Motor Position Set Minimum Throttle Position to Maximum • Fixed incorrect sensor values for older Chrysler vehicles using the SBEC controllers • Fixed the issue with bi-dir not shutting off when commanded too • Fixed the Freeze Frame Calculated Load unit value • Fixed VIN decoding for a 2002 Grand Caravan • Fixed bi-directional controls for NGC and JTEC/SBEC controllers Ford • Added PATS key programming • Added "Software Level" reporting to the Vehicle Information feature • Added Mercury Software and Vehicle Information reporting support • Added Airbag module Passenger Seat Weight Sensor ReZero procedure support • Added Falcon BF '05 - '06 support (Airbag, ECM, ICM, ABS, EATC, and 4x4) • Added Expedition '05 - '06 support (Airbag, ECM, ICM, ABS, EATC, and 4x4) • Added Ford of Europe Fusion '03 - '06 support (GEM, Airbag, ECM, TCM, ICM, ABS) • Added UPS P32 '95 - '01 support (ABS and ECM) • Added several PCM and DDM bi-directional controls • Added IAT2 V and Temperature to the Mustang '03 - '04 product line • Added Remote Anti-Theft System remote transmitter viewing and programming (some Lincoln vehicles are not supported at this time) • Added Escape Hybrid '05 - '07 support for the Hybrid Electrical Voltage system • Improved EVAP Bay Test to show EVAP Canister and Canister Vent Duty Cycle during the test • Fixed no longer showing diesel system tests for gasoline vehicles • Fixed Crown Victoria '06 enhanced powertrain not working Toyota • Added Prius '03 - '06 ABS support • Improved CAN data rates by caching multi-packet responses • Fixed Prius '03 - '06 EMPS system not working • Fixed CAN enhanced powertrain missing some supported PIDs • Fixed CAN enhanced powertrain Purge Density Learning Value displaying with incorrect decimal position • Fixed CAN DTC retrieval showing an erroneous C0100 code • Fixed Tire Pressure Warning System support not enumerating with 2006 vehicles • Fixed Total Fuel Trim Bank 1 and Bank 2 scaling bug Nissan • Added support for the Almera, Micra, Note, Patrol, Primera, Navara, Terrano, Versa models • Added Self-Learn Control and Idle Air Volume Learn support • Added CAN BCM support; including work support for Door Lock Unlock Set, Anti-LockOut Set, Horn Chirp Set, Hazard Lamp Set, Multi-Answer Back Set, Auto-Lock Se, Panic Alarm Set, Trunk Open Set, Power Window Down Set, Battery Saver Set, Custom Light Setting, Illumination Delay Set, Wiper Speed Setting, Reset Setting Value, Room Lamp Timer Set, Security Alarm Set, Theft Alarm Trigger Erase) • Improved CAN data rates by caching multi-packet responses • Fixed Throttle Sensor 1 and 2 not working • Fixed Accelerator Sensor 1 and 2 not working • Fixed 4WD system Battery voltage sensor reporting incorrectly Mazda • Added Tribute and Protege '02 model coverage (GEM, IC, PCM, ABS) • Added '96 and '97 Miata support • Fixed Tire Pressure and Temperature having incorrect scaling values • Fixed Tire Pressure Monitoring System Wheel Temperature and Pressure 4 sensor not being listed • Fixed miscellaneous typos in the sensor list • Fixed '03 Protege ABS and airbag systems not working • Fixed retrieving all CAN system DTCs instead of retrieving from the selected system only • Improved VIN decoding for all models Hyundai/Kia • Added Kia Amanti support for powertrain • Added Kia VIN decoding 03/31/2006 4.1.0 Release: ------------------------- General • Added RF wireless support • Added USB hardware serial number reporting in the About window • Added more Subaru DTC descriptions • Fixed 17th digit of VIN not showing up for Hyundai and Toyota • Fixed warning message showing that not all IM Monitors have complete when Secondary Air Monitor had completed • Fixed Playback Rate not working on the Grid control • Fixed DTC/MIL Status Information from being used on the next vehicle connection if the next vehicle doesn't support DTC/MIL Status Information • Fixed Pocket PC version DTC reports missing the first three characters of the DTC description • Fixed Pocket PC version BlueTooth connection issues where it wouldn't find the connector • Fixed KWP2000 Fast Init connection issues Ford • Added Ford FreeStyle '05 - '06 support • Added Ford GT '03 -'04 support • Added Ford of Europe support for Fairlane, Fairmont, Falcon, Galaxy, and LTD • Added Software and Vehicle Module Information to Vehicle Information support to show PCM Part #, Copyright date, Octane Adjust, Fuel Octane, Fuel Type, Tire Size, Axle Ratio, Manual Transmission settings • Fixed CAN ICP and ICP Desired sensor resolutions • Fixed Powerstroke diesel trouble code retrieval • Fixed Mode 6 $4B-30 decimal formatting Toyota • Added enhanced CAN support to include HV ECU and HV Battery systems, etc. • Added enhanced airbag, CCS, A/C, and Immobilizer systems, etc. • Added hundreds of new U and P trouble codes • Added Hilux and Yaris support • Added Vehicle Module Information to Vehicle Information support to show Model Code, Engine Type, Cylinders, etc. GM • Added DPID support (4x sampling) • Added passenger and light truck chassis support • Added Workhorse support for make and models (P42 Series, W22 Series, W24 Series, W52 Series, LF72 Series, P32 Series, W18 Series, FE20 Series, W42 Series) • Added all EVAP PIDs • Added '06 passenger (non-CAN) vehicle support • Added EVAP System test for Saturn 1.9 '98 - '02 • Added Saturn body support • Added L and M product for '00 - '01 Pontiac • Added '06 passenger vehicle VIN decoding • Fixed communication issues for some body modules • Fixed GM trouble code retrieval for some systems body controllers • Fixed GM Crank Variation Learn not being listed in some cases where support was available Hyundai/Kai • Added enhanced support for '98 - '04 Including European Hyundai Atoz, Centenial, Marcia and Kia Enterprise, Frontier, K2500, Pergio, Picanto, Pontentia, Pride MELCO and Siemens/SiemensK21 Powertrain MELCO and Siemens/SiemensK21 Transaxle • Added ECU Identification Table support to Vehicle Information support to show CAL, CAL programming date, Boot software number, ECU software number, vehicle manufacturer and supplier ECU hardware number, etc. Chrysler • Added Vehicle Module Information to Vehicle Information support to show Product Line, Engine Size, Module Name, Module Part # • Fixed sensor support table for '03 Dodge Stratus Mazda • Added CAN enhanced support for '03 - '06 • Added new systems: 4x4 Control Module CAN Anti-Lock Brakes Anti-Lock Brakes CAN Enhanced Powertrain CAN Electronic Power Steering CAN Instrument Cluster CAN Transmission Control Module CAN Tire Pressure Monitor CAN Restraint Control Module Remote Keyless Entry CAN 01/06/2006 4.0.1 Release: ------------------------- General • Added Hungarian language support • Added web-based activation process for enhanced options • Added Honda Pilot support • Added RF wireless support • Fixed German and Spanish support not being updated to version 4.0 • Fixed KWP2000 auto detection issue with some slow baud init Mercedes • Fixed Grid Units field drop-down list from ignoring a units change • Fixed Pontiac TransAm/Formula VIN decoding • Changed the update rate for DTCs and IM/Mode 6 information from 5 minutes to 10 minutes Ford • Fixed EVAP System Test not failing when fuel level is too low or high • Fixed CAN LTFT and STFT ranges being too large • Fixed CAN Throttle Position Sensors 1 and 2 not reporting the hundredths decimal places Chrysler • Added SCI serial connector support for Pocket PC/Windows Mobile and Windows PC • Added (Gas) post-fix to Dodge R2500 and R3500 to differentiate between Cummins and gas versions of the truck • Added more Dodge Dakota engine series support • Changed to default to Chrysler make by default when connected to a SCI connector • Changed Town & Country to report as Town&Country to fix XML reports from not being parsed correctly • Fixed '02 - '05 Cummins temperature sensors reporting incorrectly • Fixed Freeze Frame sensor value issues GM • Fixed retrieving DTCs from certain body controllers • Fixed '03 - '05 Trailblazer enhanced powertrain from not listing • Fixed conversion from liters to gallons certain PIDs • Fixed metric/english units issue with vehicle speed • Fixed retrieving Body module controller trouble codes by automatically setting Additional DTC Types History • Fixed Freeze Frame sensor value issues • Fixed LBY Duramax sensor errors 11/25/2005 4.0.0 Release: ------------------------- General • Added a new user-interface to support resizable windows, docking controls, and improved look-and-feel • Added support for new SAE extended "lettered" (i.e., 0x06b2) DTCs • Added triggerible data logging • Added smart updating of Live Data Grid. Only viewable sensors will be updated while not data logging • Added buttons to zoom the O2 graph to trim and voltage presets • Added support for retrieving of enhanced Cleared and History codes • Added Outlook Express email support for sending activation requests • Added a new Emissions Report to contain just the DTC list, MIL status, and IM states • Added the ability to enter a key on the Grid and the first sensor with that key will be brought to focus • Added more Kia manufacturer specific trouble codes\ • Added Vehicle Notes that can be saved with the vehicle's configuration file for latter review • Added support to quickly bring a sensor into focus on the Live Data Grid by pressing the first letter of the sensor's name • Improved O2 Sensor Test Results reporting by caching the reported data to prevent being retrieved each time • Fixed Mode 6x CAN on some Ford vehicles • Fixed Nissan 00 - 01 DTC retrieving issues • Language neutralized the ToolTips (translated in Spanish and German) • Improved timestamp reporting by changing the millisecond prefix of a colon to a decimal character (XX:XX:XX.XXX) • Improved Toyota Mode 6 scaling and translation support • Improved Subaru Mode 6 scaling and translation support Ford • Added Ford Mustang 05 - 06 all systems support • Added Ford Focus 05 - 06 all systems support • Added Ford CAN Airbag system support • Added more Tire Pressure system sensors • Added EVAP System Bay Test support • Added support for Outputs Off, Outputs On, Low Speed Fan, and High Speed Fan actuation controls • Added Powerstroke diesel DTC hints • Added VIN decoding for Freestar and Aviator • Changed all EVAP PIDs to use exact Ford terminology • Changed Injector Pulse Width from reporting in Ticks to ms • Changed Fuel Tank Pressure Input from reporting in inH20 to Pa and PSI, and increased the range • Fixed Spark Advance missing from Mustang GT 96-04 GM • Added hundreds of new GM sensors and dozens of new bi-directional controls • Improved GM sensor support by using pre-defined tables instead of auto detecting Chrysler • Added Chrysler/Dodge '02 - '05 JTEC, SBEC, NGC powertrain module support • Fixed 2004 Chrysler Town and Country VIN decoding Toyota • Fixed Fuel Tank Pressure PID from not reporting • Fixed Throttle Fully Closed Learn Value (Initial) from reporting in Deg instead of V 09/28/2005 3.6.0 Release: ------------------------- Generic • Added Mazda VIN decoding • Added Mazda 3 specific support • Fixed Jeep VINs decoding as Jaguar • Fixed Ford F150 W08 series VIN decoding not working • Fixed German User Guide not being installed Enhanced Chrysler • Added dozens of new engines series, sensors, and active commands to complete the 96-01 powertrain support • Improved actuator support by making it engine specific Enhanced Toyota • Added 33 new sensors, 35 new active commands, 1,000+ new trouble code descriptions and support up to 2005. Enhanced Ford • Added Crown Victoria enhanced CAN powertrain for 05 - 06 • Fixed Powerstroke 7.3L 99-01 showing the Engine Coolant Temperature Input. • Fixed Powerstroke 7.3L VRef not allowing values larger then 5Vs 09/08/2005 3.5.2 Release: ------------------------- Generic • Fixed allowing the window position to be saved if it was off the screen • Fixed missing VIN digit with some newer GM vehicles • Fixed not filtering superfluous GM FF and EF packets Enhanced GM • Fixed GM DTCs showing a superfluous U3F00 code Enhanced Ford • Fixed Powerstroke diesel temperature sensors still being incorrectly reported 09/03/2005 3.5.1 Release: ------------------------- Generic • Added Porsche Mode 6 support • Improved German translation. • Fixed missing In-Performance Tracking and Vehicle Information icons • Fixed CAN 6x Mode not working with USB connector Enhanced Toyota • Added support to allow generic and enhanced sensors to co-exist on the same connection SpeedTracer • Fixed USB SpeedTracer not finding the USB connector 08/19/2005 3.5 Release: ----------------------- Generic • Added USB OBD-II connector support • Added Chrysler, Dodge, Plymouth, Eagle, and Jeep VIN decoding • Added showing the wait cursor during VIN retrieval and decoding • Added new Toyota, Lexus, and Scion model VIN decoding support • Added using keyboard (Space to select and Ctrl for multi-selection) to select sensors on Grid's sensor list • Improved ISO and CAN throughput by 1Hz • Fixed Vehicle Information Dialog not displaying for Ford Powerstrokes • Fixed the Grid calculation of percentages based on a sensors range • Fixed Pause not working during Playback • Fixed Honda Mode 6 decoding EVAP CIDs Enhanced Ford • Improved enhanced actuation support by allowing multiple requests simultaneously • Fixed Ford Engine Oil Temperature showing C when it is supposed to be F • Fixed Ford F150 01 VIN decoding bug • Fixed retrieving pre-00 Ford VINs • Fixed Powerstroke 6.0L transmission not completing the auto detection phase bug Enhanced GM • Added new GM CKP tests • Improved enhanced actuation support by allowing multiple requests simultaneously • Fixed GM LS1 series not having Engine Speed sensor Enhanced Chrysler • Added Chrysler/Dodge/Plymouth/Eagle/Jeep enhanced support Enhanced Mazda • Added Mazda enhanced support 07/03/2005 3.4 Release: ----------------------- All • Added CAN In-Performance Tracking. • Added more Mercedes Benz trouble code descriptions. • Added Hyundai VIN decoding. • Added support for Enhanced Freeze Frame (multi-frames) and DTC Status. • Improved listing DTCs by sorting them ascending alphanumerically. • Improved DTC Reports to now show the multiple freeze frame entries. • Changed system names being displayed instead of manufacturer specific for specific DTCs. • Changed DTC and Freeze Frame to report in a tree structure to help associate the data relationship. • Added 900 and 2.4 Ghz wireless support. Enhanced Ford • Added support for pulling multi-system DTCs simultaneously. • Added Service Bleed. • Added KAM Reset. • Added more F150 support. • Added 2006 model year support. • Added support to pull VINs for vehicles prior to Mode 9 support. • Improved active/functional support to allow sensor viewing while actuating controls. • Fixed the range for Fuel Level Input Sensor. • Fixed ICP for PWM and CAN Powerstrokes. • Fixed bi-directional timing issues with active commands. • Fixed timing issues for system tests if run back-to-back. • Fixed Engine Oil Temp., Engine Coolant Temp., and Transmission Temp. for Ford 6.0L Powerstroke. • Fixed TPS V going from 2.48 straight to 5V without any interim steps. • Fixed Airbag resistence pids to show more decimals etc. • Fixed Fuel Tank Pressure reporting value. • Fixed Airbag Resistence to Ground PID reporting value. Enhanced GM • Added light truck body support (1996-2005). • Added support for pulling multi-system DTCs simultaneously. • Added VIN decoding for 2003 - 2005 passenger vehicles and light trucks. • Added the support for 6.5L engine series. • Improved GM light truck transmission. • Improved active/functional support to allow sensor viewing while actuating controls. • Fixed the value calculations for: 3xCrank, 18xCrank, 24xCrank, CKP Engine. • Fixed IAC position for light trucks. • Fixed GM 3/4 Shift Error. • Fixed GM Mode 6 TID 0x05 and CID 0x0a and 0x0C typo. • Fixed bi-directional timing issues with active commands. • Fixed decoding VINs and adding engine types during Vehicle Selection. • Fixed MAF decimal position. 04/15/2005 3.3 Release: ----------------------- • Added GM Body and Transmission controls (1900+ sensors and 100+ functional commands). • Added new Grid data view replacing the Dashtop. • Added VIN decoding to automatically setup the make, model, year, and related vehicle information. • Added new Powerstroke Quick Connect. (Select Ford Powerstroke for the Initialization Type.) • Added Hot Key support. • Added more Nissan DTC descriptions. • Added support for setting "Enhanced Powertrain" as default system if available. • Added an all menu items "look and feel". • Added GM '04-'05 3.5L active commands. • Added TDC Learn to the GM '96 6.5L trucks. • Added more $2A sensors for GM '96-'97 for 5.0L, 5.7L, 7.4L. • Added Ford Mustang '05 support. • Improved PWM and VPW connection times and Mode 6 pulling by as much a 2x faster. • Improved BlueTooth Wireless connectivity and throughput. • Improved auto-detect enhanced sensors algorithms for GM. • Improved auto-detect enhanced sensors algorithms for Ford by 20x faster. • Improved Freeze Frame reporting for older ISO vehicles. • Fixed Installation not adding XSL files. • Fixed MRU not dropping down previously selected Vehicle Selections. • Fixed IM and DTC reports showing 6 hours wrong time. • Fixed Toyota Mode 6 Oxygen Sensor Monitoring listing as A/C Monitoring. • Fixed Chrysler Mode 6 decoding. • Fixed Ford Enhanced O2 Inputs maximum reporting as 66V instead of 1V. • Fixed allowing Record to be initiated if no sensors are active to be recorded. • Fixed CAL and CVN reporting for some CAN vehicles. • Fixed Ford J1850 PWM Mode 6 TID 61 - 64 off by .00195. • Fixed Ford PCM ID Verified sensors to distinguish between the active/inactive state sensor or the off/on state sensor. • Fixed Ford of Europe not having DTC descriptions. • Fixed Ford Cylinder Head Temperature, FICM, Fuel Pressure, BARO, MAF, and LTFT1, and LTFT2 sensors. • Fixed GM CMP Retard, IAC, and Starup IAT sensors. • Fixed an issue with pulling older GM light truck VINs. • Fixed the decimal placing for Ford % sensors. Pocket PC specific: ------------------- • Fixed Freeze Frame and Vehicle Information windows not showing a busy cursor while coming up. • Fixed System Test tab test descriptions from being clipping. • Fixed font getting smaller on the graph tab for some Windows Mobile SE equipped devices. • Pocket PC and Palm now use the same OBD-II interface. Palm specific: -------------- • GM tranny and body support was not implemented in this revision. • Ford does not have new auto detecting from the built-in supported sensor list. • Fixed issue with graphing. 02/21/2005 3.2.1 Release: ------------------------- • Added GM Aveo, Optra, and Wave Mode 6 information. • Added more GM Active Commands for 3.0L engine types. • Added Crank Variation Learn (CKP Test) to most GM engine series. • Added increased Chevy Corvette, Duramax, and (GMC/Chevy) Suburban specific support. • Added Spanish, Hungarian, Swedish, and Greek language support. • Fixed Chrysler packet formatting errors for newer models. • Fixed Vehicle Information not showing Busy error, but instead showing no data. • Fixed Wheel Speed sensor not data logging correctly. • Improved all VIN reporting. 02/03/2005 3.2 Release: ----------------------- • Added 180 new Enhanced GM sensors. • Added 200 new Enhanced Ford sensors. • Added Enhanced Ford Active Commands (Totally 347). • Added Enhanced GM Active Commands (Totalling 200). • Added Enhanced Toyota Active Commands (Totalling 18). • Added CAN 6x support for faster throughput. • Added BMW 01-05 M3/M5 support. • Added Subaru Mode 6 and more DTCs definitions. • Added Nissan DTC definitions. • Added more TSBs. • Added automated email creation for activation codes. • Improved Nissan DTC support. • Improved connection time. • Improved CAL and CVN reading support. • Improved the graphs line plotting thickness. • Improved PDA graphing (One graph with two plots and thicker plots). • Fixed KWP2000 support. 12/19/2004 3.1.1 Release: ------------------------ • Changed DTC reporting so that mandatory four characters are shown. P300 will show as P0300. • Changed so that DTC and IM reports no longer require style sheets to be in same directory as the report. It's now pathed with the installation path of the application. • Changed Ford sensors default reporting units. • Fixed installer not allowing you to change the install directory. • Fixed Pocket PC data logging showing incorrect time for some devices. • Fixed Multiple CAL reporting for some manufacturers. • Added more Ford sensors and systems. • Added 29 new Toyota sensors (support through 2005). • Added support for Scion XA and XB to both generic OBDII and enhanced Toyota. • Added more Hyundai Mode 6 updated. • Added support to remember the last vehicle you selected. • Added support to color-code the Mode 6 value depending on Pass or Failure. • Added Mode 6 TID and CID values being shown with the descriptions. 11/29/2004 3.1 Release: ---------------------- • Changed selecting separator in the Meter and Graph drop-down to be ignored. • Changed meter background digits to not show. • Changed all Ford enhanced MAP units to PSI. • Changed ISO connections to be faster by grouping PID and MID tests. • Fixed OnBoard tab no longer clips the Please Wait message while it is updating. • Fixed crashes during closing while Playback running. • Fixed "Threshold" and "Sesnor" typo in Ford Mode 6. • Fixed Ford states sensors reporting. • Fixed multiple DTCs for ISO vehicles (packet loss) • Added Toyota enhanced Powertrain. • Added "Connecting...Please wait." after the connector is found. • Added sample Playback files to help teach OBD-II principals. • Added CAN Transmission. • Added Vehicle Information window added to show all Vehicle-related and ECM-related information (CVN ID, CVN verification IDs) • Added parsing out illegal XML characters. • Added more Toyota DTCs. • Added Auto Detecting sensors Progress Bar. • Added showing ToolTips in Vehicle Selection window. • Added Most-Recently Used list on the Vehicle Selection Browse section. • Added more fuel management information to User Guide. 09/16/2004 3.0 Release: ---------------------- • New UI. • Faster connections • Larger screen size (800 x 600) with Min. and Max. support. • Added Audible Alerts when a max range is achieved. • Added Testability and DTC/MIL-related TSBs are reported. • Added Sensor Configurations. • Added XML and CSV Playback. • Added fully translated Mode 6 support. • HeartBeat made more robust. • Added 4 new EOBD (total 83) sensors: Fuel Type, Alcohol Fuel Percentage, Absolute Evap System Vapor Pressure, Evap System Vapor Pressure (Alternate scaling). • Added Printing and Saving of DTC and IMs with customizable XML style sheets. • Added Indexible DTC Library. • ToolTips to help users know how each section of the software works. • Added Savable Configurations. • Hi-resolution logging in milliseconds. • New Install. • Made meters easier to read on laptops. • Added Save and Refresh support for DTC and IM tabs. • Ford Enhanced: Added all 66 systems are support. Added support for all 2700+ sensors. Added system tests. Added full CAN PowerStroke support. • GM Enhanced: Fixed fuel and transmission temperatures reporting incorrectly. 02/21/2004 2.2 Release: ---------------------- • Added extended Mode 6 support. • Increased the GM and Ford enhanced interfaces' auto detecting PID rate. • Added GM enhanced interface's feature to get History and Cleared codes. 02/21/2004 2.1 Release ---------------------- • Fixed O2 sensors voltage and fuel trim swap. • Added Bluetooth and RF wireless support. • Added CAN protocol support. • Added Technical Support information menu item. 01/27/2004 2.0.1 Release ---------------------- • Meters are more readable. • Fixed reporting that the connector is incorrect when in fact it isn't found. • Improved Auto Detect for ISO interfaces. • Added more trouble codes for Nissan, Toyota, Land Rover, and Acura. • Improved KWP2000 support. • Meters page won't disappear with and ESC key press. • Fixed OBDII typo. • Added the ability for troubles codes to be click to show the full description in a window. 01/05/2004 2.0 Release ---------------------- • Fixed poor Auto Detect of BMW open issue. • Added wireless support. • Added VIN support • Added support for 64 new sensors (including wide-band O2 sensors) • Added color-coded meters. • Added new trouble code descriptions. • Added GIF animated logo. • Improved the way in which we display the connection process to the user. 9/30/2003 1.2 Release ---------------------- • Added Use HeartBeat to detect a disconnect condition. • Faster connection times. • Added A/D convertor for battery voltage. • Fixed I/M monitors that didn't report keeping the Connection Status window up. • More Multiple ECU support. • Added more DTCs for 2003 and 2004 vehicles. • Fixed disconnecting from one ECU and connecting to the next before a lose in connection still showing the old vehicle's sensor list. • Added more support for Nissan ECUs. 1.1a Release ---------------------- • Fixed ISO Sync delay. • Added Please Wait when updating the Continuous and Non-Continuous monitors.